Loading

    Choose a Category

NetGain Controls WarP-Drive Performance Liquid Cooling Kit

Designed specifically with the Industrial controller in mind, this kit has both a professional appearance and the highest performance possible. It utilizes -8 AN fittings and hose throughout for a leak-free system. The radiator and fan assembly is extremely easy to mount and provides large amounts of air flow to keep your system running cool. Includes everything shown in the picture: 10 feet of extremely high quality AN tubing, a pump that can move up to 1.5 GPM through the system, a high-temp plastic reservoir, and all fittings.


$725.00

#701-WDCK-2


NetGain Controls WarP-Drive Liquid Cooling Kit


$325.00

#701-WD-CK-ST

This complete package is a collection of all the cooling components you'll need for your WarP-Drive motor controller (adapters for other controllers are sold separately below):

  • 12V high-flow super-quiet pump
  • Waterproof electrical connectors
  • 6" x 12" finned Radiator
  • 83 CFM 12V waterproof fans (2)
  • 8 ft. 1/2" ID (3/4" OD) Soft Vinyl tubing
  • Easy to use snap-grip clamps for each connection
  • Automotive quality 1/2 gallon coolant reservoir
  • 1/2" fittings for radiator and reservoir

The 120mm fans can easily be mounted to the pre-drilled holes on the radiator. If you are thinking about getting other cooling components for cheaper, consider that this kit has been researched, tuned, and refined to contain the best liquid cooling components possible for the money. It will allow for more than 1.5GPM to flow through a WarP-Drive controller.

Installation Guide

Note on electrical connections:

A relay is not included with the liquid cooling kits. Instead, we suggest the 12V, 35A relay in junction with the Bussman fuse/relay holder. This setup provides a convenient way to combine multiple fuses and relays in one container. The Bosch 12V, 20A relay is compatible with this kit and can be purchased on the relays page.


Elcon IP67 Chillplate with 90 Degree Stainless Steel Fittings

Water cooled heat sink for Eltek IP67 series chargers

  • Termally conductive material allows for proper heat transfer
  • 90 degree stainless steel 1/2" ID rotating fittings
  • Mounts directly to IP67 charger


$314.00

#701-CP-IP67

 


Liquid Cooling Adapters

When it comes to liquid cooling, a high flow rate equals high heat dissipation. The NetGain Controls liquid cooling kits have been optimized for maximum flow rate. As such, we recommend using this cooling kit for all controllers. The liquid cooling ports on the Zilla and Soliton1 are designed for 1/8in NPT whereas the WarP-Drive cooling kit uses 1/2 ID tubing or -8 AN fittings for the Performance Kit. Adapting the WarP-Drive cooling kit to the Zilla and Soliton1 is made easy with these kits.

The items below are adapter kits ONLY! This is NOT a full cooling kit. The full cooling kit is the NetGain Controls WarP-Drive Liquid Cooling Kits listed above. The adapter kits are for using the Warp drive cooling kit with the specified controllers.

Standard Kit Adapters Performance Kit Adapters

(WarP-Drive Industrial to Standard Cooling Kit:
No adapters required)

 

WarP-Drive Industrial to Performance Cooling Kit



$28.00

#701-CK2WD2

 


Soliton/Zilla Liquid Cooling Adapter Kit for Standard Cooling Kit



$23.00

#701-88000-X

Soliton/Zilla Liquid Cooling Adapter Kit for Performance Cooling Kit



$24.00

#701-CK21_8


WarP-Drive Classic to Standard Cooling Kit



$19.00

#701-CK1WD1

WarP-Drive Classic to Performance Cooling Kit



$25.00

#701-CK2WD1

2015 www.evsource.com
Logan, Utah USA